AM2320

Plugin: python.d.plugin Module: am2320

Overview

This collector monitors AM2320 sensor metrics about temperature and humidity.

It retrieves temperature and humidity values by contacting an AM2320 sensor over i2c.

This collector is supported on all platforms.

This collector only supports collecting metrics from a single instance of this integration.

Default Behavior

Auto-Detection

Assuming prerequisites are met, the collector will try to connect to the sensor via i2c

Limits

The default configuration for this integration does not impose any limits on data collection.

Performance Impact

The default configuration for this integration is not expected to impose a significant performance impact on the system.

Metrics

Metrics grouped by scope.

The scope defines the instance that the metric belongs to. An instance is uniquely identified by a set of labels.

Per AM2320 instance

These metrics refer to the entire monitored application.

This scope has no labels.

Metrics:

Metric	Dimensions	Unit
am2320.temperature	temperature	celsius
am2320.humidity	humidity	percentage

Alerts

There are no alerts configured by default for this integration.

Setup

Prerequisites

Sensor connection to a Raspberry Pi

Connect the am2320 to the Raspberry Pi I2C pins

Raspberry Pi 3B/4 Pins:

• Board 3.3V (pin 1) to sensor VIN (pin 1)
• Board SDA (pin 3) to sensor SDA (pin 2)
• Board GND (pin 6) to sensor GND (pin 3)
• Board SCL (pin 5) to sensor SCL (pin 4)

You may also need to add two I2C pullup resistors if your board does not already have them. The Raspberry Pi does have internal pullup resistors but it doesn't hurt to add them anyway. You can use 2.2K - 10K but we will just use 10K. The resistors go from VDD to SCL and SDA each.

Software requirements

Install the Adafruit Circuit Python AM2320 library:

sudo pip3 install adafruit-circuitpython-am2320

Configuration

File

The configuration file name for this integration is python.d/am2320.conf.

You can edit the configuration file using the edit-config script from the Netdata config directory.

cd /etc/netdata 2>/dev/null || cd /opt/netdata/etc/netdata
sudo ./edit-config python.d/am2320.conf

Options

There are 2 sections:

• Global variables
• One or more JOBS that can define multiple different instances to monitor.

The following options can be defined globally: priority, penalty, autodetection_retry, update_every, but can also be defined per JOB to override the global values.

Additionally, the following collapsed table contains all the options that can be configured inside a JOB definition.

Every configuration JOB starts with a job_name value which will appear in the dashboard, unless a name parameter is specified.

Config options

Name	Description	Default	Required
update_every	Sets the default data collection frequency.	5	no
priority	Controls the order of charts at the netdata dashboard.	60000	no
autodetection_retry	Sets the job re-check interval in seconds.	0	no
penalty	Indicates whether to apply penalty to update_every in case of failures.	yes	no
name	Job name. This value will overwrite the job_name value. JOBS with the same name are mutually exclusive. Only one of them will be allowed running at any time. This allows autodetection to try several alternatives and pick the one that works.		no

Examples

Local sensor

A basic JOB configuration

local_sensor:
  name: 'Local AM2320'

Troubleshooting

Debug Mode

To troubleshoot issues with the am2320 collector, run the python.d.plugin with the debug option enabled. The output should give you clues as to why the collector isn't working.

• Navigate to the plugins.d directory, usually at /usr/libexec/netdata/plugins.d/. If that's not the case on your system, open netdata.conf and look for the plugins setting under [directories].

  cd /usr/libexec/netdata/plugins.d/

• Switch to the netdata user.

  sudo -u netdata -s

• Run the python.d.plugin to debug the collector:

  ./python.d.plugin am2320 debug trace